 |
| | Connectors (Analog RGB In) | | - Active stereo 3D input via 15-pin D-sub (VESA) standard connector
- High bandwidth buffered loopthrough of active stereo 3D input via second 15-pin D-sub connector (e.g. to local monitor)
|
|
| Horizontal Frequency Range (Analog RGB In) | | |
|
| Vertical Frequency Range (Analog RGB In) | | |
|
| Scan Format (Analog RGB In) | | - Progressive, Interlaced (interlaced is handled as field sequential stereo signal)
|
|
| Input Dot (pixel) Clock Rate (Analog RGB In) | | |
|
| Active Stereo Input Formats | | - Four different formats (separate channels, above-and-below, line interleaved, interlaced field sequential)
- Input resolution from VGA 640 x 480 to SXGA+ 1400 x 1050
|
|
| Stereo Sync Input | | - Separate H and V, Composite, sync-on-green
- 3-pin mini-DIN stereo sync input connector
|
|
| Connectors (Analog RGB Out) | | - Passive stereo outputs for left-eye and right-eye in analog RGB formats via two 15-pin D-sub connectors
|
|
| Horizontal Frequency Range (Analog RGB Out) | | |
|
| Vertical Frequency Range (Analog RGB Out) | | - Any vertical frequency within the limits of pixel clock
|
|
| Scan Format (Analog RGB Out) | | |
|
| Output Dot (pixel) Clock Rate | | |
|
| Stereo Sync Output | | - Separate H and V
- 3-pin mini-DIN stereo sync output connector
|
|
| Connector (Digital RGB Output) | | - Passive stereo outputs for the left-eye and right-eye in digital RGB formatts via two DVI-D connectors
- Compliant with DVI 1.0 (single link)
|
|
| Stereo Sync Output (Digital RGB Output) | | - Separate H and V
- 3-pin mini-DIN stereo sync output connector
|
|
| Control/Networking | | - Built-in keypad (Menu, User button, "Right black button" for setup and 2D viewing, Internal Stereo Sync Toggle button and Power on/off)
- Built-in RS232 communication port (RJ45)
- Built-in RJ45 link port to network multiple converters
- Intuitive on-screen display menus for ease of setup
- Pixel tracking and phase adjustments
|
|
| Additional Features | | - Installation mounting flexibility (upright or inverted orientation)
- Upgradeable firmware
- Auto set-up
- Two built-in diagnostic LEDs
- Standby mode
- Factory setting mode
- Estimated MTBF:100,000 hours
|
|
| Power Requirements - AP Converter | | - Connectors: 5.5/2.5mm diameter power jack
- Voltage Range: 100 - 240VAC +/- 10%
- Power Consumption: 20W
|
|
| External Power Requirements | | - Voltage Range (auto-switching): 100-240 VAC +/- 10%
- Line Frequency: 50Hz - 60Hz nominal
- Current Rating: 0.6A
- Current Rating of AC Input Connector: 2.5A
|
|
| Size | | - 8.27" L x 9.84" W x 2.75" H
- 210mm L x 250mm W x 70mm H
|
|
| Weight | | |
|
| Environment | | - Operating Temperature: 0-50° C
- Humidity: 20% - 80% non-condensing
- Storage Temperature: -20° C to +70° C,
Storage Humidity: 0% - 90% non-condensing
|
|
| Standard Accessories | | - 1 Power transformer
- 1 110 VAC cord
- 1 220 VAC cord (European)
- 1 RGB computer cable (15-pin D-sub male/male)
- 1 serial RS232 cable, RJ45 to 9-pin D-sub female
- 1 3-pin mini DIN stereo sync cable
- 1 pair left and right hand linear polarized acrylic filters (size 4" x 4", 45 degree orientation and transmission 38%)
- 1 filter stand
- 10 pairs linear polarized glasses
- User's manual
|
|
| Regulatory Approvals | | - Safety: CSA C22.2 No. 950, UL 1950, EN609050 European Norm "Safety of Information Technology Equipment"
- Complies with relevant worldwide EMC safety standards
- The product complies with FCC class A and EN55022 Class A requirements
- This product conforms to all relevant European directives, safety, health and environmental concerns and bares the CE marking
|
| |
Due to constant research, specifications and features are subject to change without notice.
|